USB 2.0+1394a+Ultra ATA/133 RAID Combo

Part No. 1016-0003-000A
( Product may vary from this image.)


 

Key Features & Benefits:
Combo card design adds USB 2.0, 1394 (FireWire®) and Ultra ATA/133 interface into your computer at once!
Supports various types of USB 2.0/1.1 and 1394 devices including removable drives, CD-ROM/DVD-ROM drives, printers, scanners, memory card readers, hubs, digital cameras, DV-camcorders, PDA and more
RAID configurations protect your system from catastrophic disk failures and system down time while doubling the data transfer rates of your hard disk drives
Breaks the 137GB barrier! Supports various types of large capacity hard disk drives. And
achieves burst data transfer rates up to 133MB/sec when connect to Ultra ATA/133 drives
System Requirements:
Pentium or equivalent PC computer with one available PCI slot
Windows® 98SE or above
Specifications:
Version: v1.0
Regulatory approval(s): FCC Class B (DoC) & CE (1998)
OS support: Windows® 98SE/2000/ME/XP
Port type 1: 3 external and 1 internal USB 2.0 ports
Port type 2: 2 external and 1 internal IEEE 1394a ports
Port type 3: 2 internal IDE 40-pin connectors
Hot-swapping feature allows you to connect/disconnect USB and 1394 devices without powering down the system
Full compliant with PCI Plug-n-Play 2.2
USB 2.0 interface:
  - Compliant with USB specification rev. 2.0
- Supports high-speed (480Mbps), full-speed (12Mbps) and low-speed (1.5Mbps) data transfer modes    for simultaneous operation of multiple USB 2.0/1.1 devices
- Works with various types of USB devices including hubs, PC video cameras, printers, scanners CD-   R/Ws, DVD-ROMs, memory card readers, removable drives, digital cameras, and more
1394a (FireWire) interface:
  - IEEE 1394-1995, P1394a (rev.1.1) and OHCI Interface Specification 1.0 compliant
- Supports serial bus data transfer rates of 100, 200 and 400Mb/sec
- Works with various types of 1394 devices including DV camcorders/cameras, hard disk drives, CD-   RWs, /DVD-ROMs, removable drives, scanners, and other audio/video devices
Ultra ATA/133 RAID controller interface:
  - Compliant with Ultra ATA/133 specification and PCI v2.2/v2.1 Plug-n-Play
- Full backward support for Ultra ATA/100/66/33 standards
- On-board flash BIOS for future upgrade
- Supports Ultra DMA 0, 1, 2, 3, 4, 5, 6 and Multi-word DMA 0, 1, 2
- CRC error-checking provides data verification and achieves flawless data transfer
- RAID 0 (striping) interleaves data across multiple hard disk drives, which increases disk system    performance dramatically.
- RAID 1 (Mirroring) simultaneously writes data to two hard drives for data redundancy.
- RAID 0+1 (Mirroring + Striping) the best of both worlds – combines mirroring and striping – four hard    drives required for this mode.
- Acts as a conventional (non-RAID) controller when not configured for RAID
- On-board BIOS supports booting from attached hard drive or stripe set
- Auto-detects drive types and fine tunes to the best performance for each Ultra ATA hard disk drives
- Support scatter/gather, multi-threaded, multi-tasking and automatic FIFO threshold selection
- Provides two independent Ultra ATA channels for faster data transfer
- Full support ACPI (Advanced Configuration and Power Interface) for advanced system power    management
   
Package Contents:
USB 2.0+1394a+Ultra ATA/133 RAID
Two Ultra ATA flat cable
Quick installation quide
Driver software

 

| About US   | News   | Products   | Service & Support   | OEM/ODM   | Contact US

 


© 2012 AVLAB Technology Inc. All rights reserved.